Melts snow without heater
Overview
The CS705 is a snowfall adapter that converts a standard 8 in. tipping bucket rain gage to a year-round rain and snow gage. It is typically used with our TE525WS rain gages.
The CS705 consists of the following:
- One black catch tube
- One reservoir
- One overflow (measurement) tube
- One 14807 drain funnel
- Two stainless-steel band clamps
- One set of CM270 mounting hardware
Solid precipitation is gathered in the catch tube and mixed with a non-toxic propylene glycol and ethanol (PGE) solution inside the reservoir. The PGE solution lowers the melting point of the frozen snow and allows the resulting liquid solution to flow through the overflow tube and be measured with a standard 8 in. rain gage.
Read MoreBenefits and Features
- Melts snow without a heater and therefore eliminates the current consumption associated with heaters
- Converts a TE525WS to a rain and snow gage
- Collects PGE/precipitation mixture below the rain gage for disposal according to local requirements
Images
Technical Description
The CS705 consists of a propylene glycol and ethanol (PGE) reservoir, overflow tube, and catch tube. Snow captured in the catch tube dissolves into the antifreeze. The melted snow raises the level of the antifreeze and water solution. The mixture flows through the overflow tube into the tipping bucket where it is measured by the tipping bucket mechanism.
Measurement Delays
The CS705 possesses inherent delays and is not suitable for real-time precipitation measurements. The following factors contribute to the delays:
- Temperatures of air and liquid in the reservoir
- Surface tension in the overflow tube
- Form of the precipitation
For rainfall at 25°C, a delay of minutes is expected after the gage receives a minimum accumulation of ~0.03 inches. For snowfall, a delay of hours to tens of hours is expected. The longest delays should be expected for low-density snows at very cold air temperatures. However, all precipitation falling into the catch tube eventually flows through the overflow tube and is measured by the tipping bucket rain gage.
Recommended Mixture
The CS705 requires a specific 1:1 formulation of propylene glycol and ethanol (PGE) to function properly. PGE is available from Campbell Scientific in a package of four, one-gallon containers (see Ordering Information). Due to regulatory restrictions, PGE can only be shipped in multiples of four gallons via UPS Ground and cannot be shipped outside of the continental US.
Why Straight Car or RV Antifreeze is NOT Recommended
Standard RV antifreeze consist of propylene glycol or ethylene glycol, which has a specific gravity of greater than 1. This allows a layer of water to sit on top of the antifreeze. That layer of water can then freeze and form an ice cap that prevents snowfall from being dissolved in the solution. Cutting the antifreeze with ethanol solves the specific gravity issue and prevents the ice cap. PGE is also more environmentally friendly.
Disposing of PGE Mixture
Although PGE is non-toxic, the PGE/precipitation mixture from the tipping bucket gage should be captured and disposed of properly in accordance with local, state, and federal regulations.
Specifications
| Compatible Antifreeze Mixture |
1:1 mixture of propylene glycol and ethanol (PGE) Campbell Scientific does not recommend using the antifreeze that is typically used in cars or RVs; refer to the Compatibility section for more information. |
| Material | Powder-coated aluminum |
| Capacity | 20.3 cm (8 in.) of liquid @ -20°C (assuming 1:0 starting ratio of antifreeze to water) |
| PGE Reservoir Capacity | 9.46 L (2.5 gal) |
| PGE Reservoir Diameter | 20.96 cm (8.25 in.) |
| PGE Reservoir Height | 35.6 cm (14 in.) |
| Catch Tube Orifice | 20.3 cm (8 in.) |
| Catch Tube Height | 25.4 cm (10 in.) |
| Weight |
|
Compatibility
Tipping Bucket Rain Gages
The CS705’s specially shaped cylinder allows it to mount to the 8-in. orifice of the TE525WS Tipping Bucket Rain Gage. The CS705 cannot be directly used with the TE525, TE525MM, CS700, TB4, or TB4MM tipping bucket rain gages. Both the TE525 and TE525MM can be converted to a TE525WS by returning them to Campbell Scientific.
Mounting
The CM270 Mounting Kit is included with each purchase of the CS705 Snowfall Adapter. The kit consists of a funnel, two band clamps, and mounting hardware. The funnel drains the antifreeze/precipitation mixture into a pail. One of the band clamps secures the top of the CS705 to a pole. The other band clamp attaches the funnel and the bottom of the rain gage to the pole.
A user-supplied pole or a CM300-series mounting pole may be used. The user must provide a pail and a hose with a 0.5 in. inner diameter. The hose must be long enough to span the distance from the funnel outlet to the pail.
Resources and Links
Product Brochures
FAQs for
Number of FAQs related to CS705: 5
Expand AllCollapse All
-
Yes. In the Quickstart section of the instruction manual, Figure 4-1 and Figure 4-2 provide labeled images of the parts with their corresponding part numbers.
-
Yes. Mixed rain and snow does not cause any issues for the CS705.
-
The CS705 works with the TE525WS-L rain gage.
-
Generally, the antifreeze is changed after 8 inches of liquid water have been added to the antifreeze/ethanol mixture. Eight inches of water will dilute the antifreeze/ethanol mixture to the point where freezing will occur at -20 degrees Celsius.
-
The CS705 Tipping Bucket Snowfall Adapter cannot be used directly with the TE525-L or TE525MM-L because of the funnel size. To make the rain gages compatible, they can either be sent to Campbell Scientific to be converted to a TE525WS-L, or an 8 inch funnel can be installed. If the funnel is used, see the instruction manual for the appropriate multipliers, as they will change.
Privacy Policy Update
We've updated our privacy policy. Learn More
Cookie Consent
Update your cookie preferences. Update Cookie Preferences