The 108-LC is a version of the 108 that has a cable terminated in a connector rather than the standard pigtails. The connector can be attached to the CS110 lightning meter or to the ET107, ET106, or MetData1 weather stations.
The 108-L is a rugged, accurate probe that measures temperature of air, soil, or water from -5° to +95°C. Designed for durability and ease of installation/removal, the 108-L easily interfaces with most Campbell Scientific dataloggers.Read More
For this version of the 108 thermistor, the cable terminates in a connector rather than the standard pigtails. The connector can be attached to the ET107 Weather Station, ET106 Weather Station (retired), or MetData1 Weather Station (retired).
The 108-LC can be used to accurately measure the temperature of a variety of media, most commonly air, water, and soil. It consists of a thermistor encapsulated in a cylindrical aluminum housing. The 108-LC measures the range of -5° to +95°C; to measure the -35° to +50°C temperature range, see the 107-LC probe.
The 108-LC is suitable for shallow burial only. It should be placed horizontally at the desired measurement depth to avoid thermal conduction from the surface to the thermistor. Placement of the sensor cable inside a rugged conduit may be advisable for long cable runs, especially in locations subject to digging/mowing, traffic, use of power tools, or lightning strikes.
|Sensor||BetaTherm 100K6A1IA Thermistor|
|Tolerance||±0.2°C (over 0° to 70°C range)|
|Temperature Measurement Range||-5° to +95°C|
|Steinhart-Hart Equation Error||≤ ±0.01°C over measurement range (CRBasic data loggers only)|
|Time Constant in Air||30 to 60 s (in a wind speed of 5 m s-1)|
|Maximum Submersion Depth||15.24 m (50 ft)|
|Probe Diameter||0.762 cm (0.3 in.)|
|Probe Length||10.4 cm (4.1 in.)|
|Weight||136 g (5 oz) with 3.05-m (10-ft) cable|
The cable of the 108-LC provides a connector that attaches to the ET107 Weather Station, ET106 Weather Station (retired), or MetData1 Weather Station (retired). The ET107 Weather Station has an on-board CR1000M module. Both the MetData1 Weather Station and ET106 Weather Station have an on-board CR10X module.
When exposed to sunlight, the 108 must be housed in a radiation shield. It is typically housed in a 41303-5A 6-plate naturally aspireated shield. It may also be housed in a 41003-5 10-plate shield if a 41322 Adapter Plate is used.
To measure large numbers of probes, the AM16/32B multiplexer is recommended.
Number of FAQs related to 108-LC: 7
Expand AllCollapse All
The thermistor is located approximately 3 mm (0.125 in.) back from the probe tip.
For both of these services, calibration can be made at different values if it is requested by the purchaser at the time of purchase. In addition, both of these calibration services can be requested after sensor purchase using a returned material authorization (RMA) number. To request an RMA number, refer to the Repair and Calibration page.
The sensor/probe consists of a non-linear thermistor configured with a precision resistor in a half-bridge circuit, as shown in the product’s manual:
To measure the sensor/probe, the measurement device has to provide a precision excitation voltage (Campbell Scientific data loggers use 2000 mV), measure the voltage across the precision resistor, determine the thermistor resistance (Ohm's law), and convert the resistance to temperature using the Steinhart-Hart equation.
The Steinhart-Hart equation is 1/T = A + Bln(R) + C(ln(R))3 where:
For the 107-L, 107-LC, 108-L, and 108-LC, the following are the coefficients for the Steinhart-Hart equation:
For the 109-L, the following are the coefficients for the Steinhart-Hart equation:
Most Campbell Scientific sensors are available as an –L, which indicates a user-specified cable length. If a sensor is listed as an –LX model (where “X” is some other character), that sensor’s cable has a user-specified length, but it terminates with a specific connector for a unique system:
If a sensor does not have an –L or other –LX designation after the main model number, the sensor has a set cable length. The cable length is listed at the end of the Description field in the product’s Ordering information. For example, the 034B-ET model has a description of “Met One Wind Set for ET Station, 67 inch Cable.” Products with a set cable length terminate, as a default, with pigtails.
If a cable terminates with a special connector for a unique system, the end of the model number designates which system. For example, the 034B-ET model designates the sensor as a 034B for an ET107 system.
Not every sensor has different cable termination options. The options available for a particular sensor can be checked by looking in two places in the Ordering information area of the sensor product page:
If a sensor is offered in an –ET, –ETM, –LC, –LQ, or –QD version, that option’s availability is reflected in the sensor model number. For example, the 034B is offered as the 034B-ET, 034B-ETM, 034B-LC, 034B-LQ, and 034B-QD.
All of the other cable termination options, if available, are listed on the Ordering information area of the sensor product page under “Cable Termination Options.” For example, the 034B-L Wind Set is offered with the –CWS, –PT, and –PW options, as shown in the Ordering information area of the 034B-L product page.
Note: As newer products are added to our inventory, typically, we will list multiple cable termination options under a single sensor model rather than creating multiple model numbers. For example, the HC2S3-L has a –C cable termination option for connecting it to a CS110 instead of offering an HC2S3-LC model.
Note the difference between calibration and a field check. Calibration cannot be done in the field, as it requires an experienced technician and specialized equipment.
Field checks of measurements can be done to determine if the data make sense with the real-world conditions. Follow these steps to field check a sensor:
Many Campbell Scientific sensors are available with different cable termination options. These options include the following:
Note: The availability of cable termination options varies by sensor. For example, sensors may have none, two, or several options to choose from. If a desired option is not listed for a specific sensor, contact Campbell Scientific for assistance.