The CS526 probe measures pH using state-of-the-art ISFET technology. There is no glass bulb to break, making the probe safer and more rugged. The probe is easy to clean, and can be stored dry.Read More
The CS526 uses SENTRON’s high-tech, ion sensitive field effect transistor (ISFET) semiconductor as its pH-sensitive element, and includes a silver/silver chloride– potassium chloride reference system. The CS526’s design allows it to be suitable for a variety of liquid pH-monitoring applications. The electronics are safely embedded in a durable PEEK body. Elimination of the glass bulb removes the possibility of broken glass, making the CS526 more rugged and safer to use.
Note: Campbell Scientific warranty does not cover a clogged reference diaphragm or improperly cleaned or maintained ISFET chip. (See the Maintenance section in the instruction manual for more information.)
This sensor requires the 5 V output on the data logger to be powered..
|pH Range||2 to 12|
|Power Requirements||5 Vdc|
|Current Consumption||15 mA (maximum)|
|Accuracy||±0.2 pH (over 10° to 40°C)|
|Operating Temperature Range||10° to 40°C|
|24 h Drift||< 0.15 pH (after 15 min. soak in pH 7 at 25°C)|
|Allowed Water Pressure||0 to 700 kPa (0 to 101.5 psi)|
|Cable Type||Three-twisted pair, 24 AWG cable with Santoprene jacket|
|Sensor Material||Polyetheretherketone (PEEK)|
|Maximum Cable Length||100 m (328 ft)|
|Diameter||16 mm (0.63 in.)|
|Length||102 mm (4 in.)|
|Weight||318 g (11.2 oz) with 3.05 m (10 ft) cable|
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Number of FAQs related to CS526: 15
Expand AllCollapse All
The CR300 and CR310 dataloggers do not support TTL logic, which is what the CS526-L sensor uses. A TTL to RS-232 converter (supplied by the user) could be used, however.
PolyEtherEtherKetone (PEEK) is a plastic material that has very good thermal stability and chemical resistance properties. This material was chosen for use in the manufacture of the CS526-L because of its natural resistance to organic acids (acetic, carbonic, citric, tartaric, etc.) and its hydrolysis resistance to fresh and saltwater.
The source and the drain are two of the three electrodes contained within the ISFET chip, and they behave in much the same way. The third electrode in the ISFET chip, the gate, has an electrical field that influences the current that flows between the source and the drain. The electrical potential in the ISFET pH sensor is measured between the reference electrode and the source.
In an ISFET chip pH sensor, the chemical coating on the gate electrode can vary depending on the model and manufacturer of the pH sensor. Depending on which chemical coating is used and what elements are present in the sample solution, there may be some ion interference.
An ISFET chip pH sensor has three main components:
A reference electrode can become contaminated when poisoning ions such as lead, iron, chrome, cyanide, or sulfide enter the reference electrode and react either with the silver wire or with the electrolyte solution.
The contamination may not become apparent until the silver-chloride coating is completely dissolved and the electrical potential from the reference electrode has changed greatly. If this occurs, the reference electrode must be replaced.
Silver is the best electrical conductor of all the metals because it has the lowest electrical resistance. The silver wire, coated in silver chloride, is relatively insensitive to changes in temperature.
Cleaning and/or calibration may be required when the measurements are scattered, drifting occurs, or there is physical evidence of fouling. Measurements for pH must be monitored regularly to check for scattering. However, just because the results are scattered does not necessarily indicate the need for an adjustment. For example, there may be a change in the water source that causes the scattering. As a sensor ages, however, the scattering of the measured values tends to increase.
To check the performance of a pH sensor, use it to measure a buffer solution in the correct range. If the value returned is within the specified range, the sensor does not need to be calibrated.
The CS526-L pH sensor uses an ISFET chip instead of pH-sensitive glass, which is used for many other pH sensors. The ISFET chip is a transistor coated with a chemically sensitive material. One of the ISFET chip’s electrodes (the gate) and the reference electrode are submersed in the same sample solution. A circuit path is established between the two electrodes. The difference in electrical potential between the two electrodes is directly proportional to the sample solution’s pH. Thus, by measuring the electrical potential, the pH is measured.
Not every sensor has different cable termination options. The options available for a particular sensor can be checked by looking in two places in the Ordering information area of the sensor product page:
If a sensor is offered in an –ET, –ETM, –LC, –LQ, or –QD version, that option’s availability is reflected in the sensor model number. For example, the 034B is offered as the 034B-ET, 034B-ETM, 034B-LC, 034B-LQ, and 034B-QD.
All of the other cable termination options, if available, are listed on the Ordering information area of the sensor product page under “Cable Termination Options.” For example, the 034B-L Wind Set is offered with the –CWS, –PT, and –PW options, as shown in the Ordering information area of the 034B-L product page.
Note: As newer products are added to our inventory, typically, we will list multiple cable termination options under a single sensor model rather than creating multiple model numbers. For example, the HC2S3-L has a –C cable termination option for connecting it to a CS110 instead of offering an HC2S3-LC model.